Search results

Have for sale set of shocks and springs for later Spyder, very little use. shocks Part nos 200216 and 200218 Springs 197895 and 197890. Mostly complete. Bought for my 2002 car to replace the skyhook shocks but they are NOT repeat NOT suitable for the early less stiff cars. Both the spring and...

One idler pulley matches a Beemer part, I posted it in the alternative parts. The tensioner pulley I could not find a match for the Dayco part no is not listed on the Dayco site. Must be a special for Maserati only.

Yes well mine is getting covered in dust and used as a cat bed..... havn't progressed much. Haven't sent ram details off to company who said they could make them. As regards the top canvas I have seen aftermarket ones advertised for about US$ 1,600 - as they are so expensive you can get one...

Make sure the torque tube bearing mod is done if it hasnt been. There is a TSB on it, basically quite crude, fit a new bearing, dot punch the housing and loctite it. Mine had been spinning in the housing. Clutch sensor is recommended to be changed also or was that mentioned.

I'm pretty sure what has been glued to the ram is non standard, i had a brain wave and looked at the bottom ram on the lhs which throws the entire top over and the arrangement appears completely different. it is only a small switch instead of a full length pot. It is in a shrink fit sleeve so i...

Hi Tubber My roof is black and the car is a black metallic so it will look at bit strange in blue I think. Plus it needs new plastic back window by the look of it, could get one made up locally I think but again more cost I will very interested in parts off yours mainly those two rams. Please PM...

Spydernick How did you get the rear screw catches to release manually, I had to unbolt mine off the rear frame. I looked at the top from Europarts, its one way out but i have spent so much on this **** car already and it cost an arm and a keg to get it sent out here. Tubber Yes I would be...

Tx for all the quick responses. I'm in the Middle East but would still welcome any assistance and provide accommodation and beer!! its a bit warm at the moment and I have to keep on coming in to cool off, 40c plusl SpyderNick,I'll gladly buy your old ram name your price. There are places who...

I don't know if anyone can help. The soft-top on my 4.2 spyder has never worked. The last owner told me it had lost the sequence. He has since left the country. I could not get the top to do anything, even could not get it to release. When it was the main agent for some work on a bad electrical...

Catman Hmm. Think I binned the seized inserts. I am away for 2/3 weeks but next time I'm in Zarooni the local hardware emporium I will try to remember to look for them and take some pics. I think they were 8 mm fine threads inside. One of the machine shop ones has pulled our I think as it did...

Not exactly an alternative part, but if you ever have to remove the rear spoiler that the exhausts go through you will probably find that the metal inserts come unscrewed with the countersunk torq screws it is fixed in with. I had some metal inserts made which didn’t work too well. After I...

bosch 0258003819

Two new sensors, Bosch, ordered by mistake for my 4200. They are for the 3200. GBP 100/pair plus postage

Yes I am interested in them if still availalble. Not sure about the 178246 part no, this is different to the one you quoted above, 175221, which shows up on the parts system.

its a 4.2 spyder 2002. I hydrolocked the engine (in the Middle East!) and have just put another engine in. Its in the main agent to have the new clutch set. They tell me it needs a new F1 ECU, it has the later ECU fitted and they are N/A in Italy. Just trying to figure out the next move...

On my 4.2 spyder there is a plastic trim around the lock and across the boot above the number plate. This also contains the rear no plates lights. There are three cross head screws whcih hold this on on to the boot on mine. They dont match so may not be standard. Remove screws and you can feed...